CCTV take-off you can defend.
Every camera counted by type and by floor from the tender drawings, checked by a person, then carried through cable, switch ports and a BOQ priced in AED from your own suppliers. Written for how tenders are priced in the UAE, Saudi Arabia and Qatar.
Below: what a CCTV take-off involves on a GCC tender, what TrueQty does at each step today, and where it stops.
Not one number. A table of camera types by floor.
On a GCC tender the consultant’s camera schedule is often incomplete or a revision behind, so the drawings are the source and the schedule is the check. What comes out is a table: floors as rows, camera types as columns, every cell traceable to a sheet.
The full method, with a worked 108-camera example, is in CCTV take-off from drawings.
- 01
Register the sheets
Every CCTV floor layout, plus the site plan, roof, car park and gatehouse, each with its revision. The riser and the schematics are kept as reference: they confirm the count, they are not counted from.
- 02
Fix the camera types
From the legend, the tags and the specification: dome, bullet, PTZ, ANPR, lift car, and the performance class each camera must reach (detection, observation, recognition, identification). An identification dome and an observation dome look the same on plan and are two BOQ lines.
- 03
Count each type, floor by floor
One type at a time. The symbols in the legend panel and the coverage wedges are not cameras. A typical floor is counted once and multiplied in writing: 6 × 7 = 42, never an unexplained 42.
- 04
Reconcile
Each sheet against the total the consultant prints, and the project against the riser. A camera that is labelled but never drawn is the miss that costs most often.
- 05
Derive what the cameras imply
One cable run per camera inside the 90 m permanent link, switch ports per floor with spare, patch panels from the runs, cable in whole 305 m boxes. The PoE budget of each switch is checked against its data sheet.
- 06
Apply the authority’s rules
In Dubai, SIRA’s specification turns into lines: outdoor cameras at least IP66, wide dynamic range where a camera faces light, recording for not less than 31 days with 20% extra capacity, and the system on UPS for at least 30 minutes. In Saudi Arabia the retention period comes from the Ministry of Interior’s requirements, so SIRA’s 31 days do not carry over.
From the drawing to a priced CCTV BOQ, a person checking every count.
Eight steps, in the order an estimator works them. Press R to see what each sentence was checked against.
- 01
Files the set
Each sheet is filed by system, drawing type and floor, read from its title block and drawing number. A floor layout is counted; a riser or a schematic is kept for reference.
- 02
Reads the cameras by type
On a vector PDF, TrueQty reads the CAD structure kept in the file and the tag beside each symbol, so cameras arrive sorted by type, with the performance classes kept apart. A code it has not met is counted as a generic camera and listed under Device types to set, with what the sheet’s legend says about it. A team lead confirms the type once, for every later drawing of your firm.
- 03
A person checks every camera
Review is one camera type at a time: only that type shows, each camera ringed where it was drawn. Step through them, take out what is not a camera, add a missed one by hand, then mark the whole type checked in one click. Approve counts belongs to a team lead or an admin.
- 04
Multiplies typical floors only on approval
A typical floor drawing is marked with the floors it covers, the preview shows the sum, and the multiplier does nothing until a team lead approves it.
- 05
Lays the count out by floor
Approved counts land in BOQ by floor: floors as rows, camera types as columns split by class, in the column wording main contractors use. Click any number and the drawings behind it are listed, each opening with only those cameras shown. Export to Excel keeps live totals and a sheet listing the source drawings.
- 06
Derives cable and switch ports from rules you can see
Each camera takes a switch port and a cable run. Per floor, the rules work out cable at route plus slack, patch panels, organisers and switches with spare ports, and each line says how it was worked out. A run over 90 m is flagged. The defaults (10% slack, 20% spare, 48-port switches, 24-port panels) are your firm’s to change, or one project’s.
- 07
Prices from your suppliers
Download a price request for your suppliers and read their quotes back, or match from saved price lists to the cheapest vendor who stocks each line, in date.
- 08
Issues the client’s copy and the proposal
Set a markup on the BOQ or on a line. Export to Excel is the client’s copy at sell price, with no cost, markup or vendor in it. The proposal is made at sell, previewed first, as a PDF and an editable Word file.
One ring per camera, and the ring says who has looked.
On the review screen every camera is ringed where it was drawn, and the ring changes when a person checks it. A checked camera means a person looked at it, never that the software was sure.
- Found, not checked
Read from the drawing. Nobody has looked yet.
- Checked
A person looked at it and kept it.
- Not sure
Read, but worth a second look.
- Added by hand
Missed, then placed by a person.
- Not a device
Taken out of the count. One click puts it back.
The review screen’s marker key, redrawn
Where the consultant prints a camera total on the sheet, TrueQty compares its count with it in one line above the drawing, and a riser’s project total is checked against all the drawings together. Flags point at the usual misses: a camera named but never drawn, a shape far larger than the others, a floor with none of a camera its neighbours have. See the count check.
The count, in the columns the main contractor asks for.
Floors down the side, camera types across the top, each type split by the class the consultant specified. IDF racks are taken from the riser, not counted on the floor layouts.
Doing it in a spreadsheet instead? The free ELV BOQ template has the same layout, with the cable and switch rules as formulas.
| Floor | IDF ref. | Dome ceiling mounted camera | Bullet camera W/P | PTZ | Lift camera | IDF rack | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| ID | REC. | OBS. | DET. | REC. | OBS. | OBS. | OBS. | |||
| Basement 1 | IDF-B1 | 2 | 0 | 6 | 12 | 0 | 0 | 0 | 0 | 1 |
| Ground floor | IDF-GF | 4 | 2 | 8 | 2 | 4 | 2 | 2 | 0 | 1 |
| Level 01 | IDF-01 | 1 | 1 | 6 | 0 | 0 | 0 | 0 | 0 | 1 |
| Roof | IDF-RF | 0 | 0 | 0 | 0 | 2 | 0 | 0 | 3 | 0 |
| Total | 7 | 3 | 20 | 14 | 6 | 2 | 2 | 3 | 3 | |
What it does not do, said before you find out.
A take-off tool that hides its limits hands you a number that looks finished and is not. These are the edges, today.
- Limit
It counts switch ports. It does not size PoE.
Each camera takes a port and switches are sized by ports with spare. The per-port class and the power budget of each switch are checked by the engineer against the data sheet, with the arithmetic in the PoE switch guide.
- Limit
It does not size recorders, storage or the UPS.
Those lines come from the specification and, in Dubai, from SIRA’s retention and UPS rules. The CCTV BOQ guide works through them from the camera count.
- Limit
It does not check the design.
Coverage, pixel density for the DORI levels and compliance with SIRA are the consultant’s design. TrueQty counts what is drawn and flags what looks missing.
- Limit
Most cable lengths are averages until the rack is on the plan.
Each cable schedule row says whether its length was measured to the rack’s position on the plan or estimated by the floor’s average run. Where the rack appears only on the riser, every run is an average, and the schedule says so.
- Limit
Scans and flattened sheets need more of a person.
On a flattened sheet you point at one camera and TrueQty finds the others like it; a person names the set and adds any it missed. A scanned sheet is counted by hand on the drawing.
- Limit
A new consultant’s conventions are taught once.
Cameras arrive typed for the conventions TrueQty has been taught. A consultant whose codes are new comes in as generic cameras for a team lead to set, once.
- Limit
A DWG or DXF cannot be checked on its own.
Only a drawing that can be shown can be checked and approved, so a CAD file never reaches the BOQ by itself. Upload the PDF exported from CAD, the most accurate, or convert the sheet to PDF here and check every camera against it. The PDF becomes the counted copy.
CCTV take-off, asked plainly.
What is a CCTV take-off?
A CCTV take-off is the count of every camera on a set of tender drawings, by camera type and by floor, with each number traced to the sheet it came from. It is the table the CCTV section of the BOQ is built from: recorders, storage, switches, cable and the UPS all follow from it.
How do you count CCTV cameras from tender drawings?
Build the camera types from the legend, the tags and the specification, then count each sheet one type at a time. Leave out the legend panel and the coverage wedges, count a typical floor once and multiply it in writing, and check each sheet against the total the consultant prints and the project against the riser.
How many switch ports does a CCTV system need?
One port for every IP camera, plus one for each access control door controller on the same network, counted per floor rack rather than per building. Add the firm's spare, commonly 20 percent, round up to whole switches, then check each switch's PoE budget and per-port class against its data sheet.
Does TrueQty count the cameras for you?
On a vector PDF it reads the cameras by type from the drawing, for the consultant conventions it has been taught, and a code it has not met is set once by a team lead. A person then checks every camera type before a team lead approves the drawing, and only approved counts reach the BOQ. No drawing is taken off without a person.
Does it work on scanned or flattened CCTV drawings?
On a flattened sheet you point at one camera symbol, TrueQty finds the others like it, and a person names the set and adds any it missed. A scanned sheet is counted by hand on the drawing. Either way each camera is checked before it is priced.
What does SIRA change in a Dubai CCTV BOQ?
SIRA's specification sets cameras at no less than Full HD, outdoor cameras at IP66 or better, recording for not less than 31 days with 20 percent extra storage, and the system on UPS for at least 30 minutes. TrueQty counts the cameras by type and floor; recorders, storage and the UPS are sized by the engineer from those rules.
Can I price the CCTV BOQ in AED from my own suppliers?
Yes. Send your suppliers a price request exported from the BOQ and read their quotes back, or match each line from saved price lists to the cheapest vendor who stocks it in date. A line nothing matches stays open. Set a markup, export the client's copy at sell price, and make the proposal from it.
Bring one CCTV floor layout.
Upload a floor layout from a tender you are pricing now. Check the cameras type by type, approve the drawing, and read the BOQ by floor, the switch ports and the cable that come out of it, each line with its working.
Priced in AED on tenders and seats, every ELV discipline included. See the plans.
