Skip to content
CH 05 · Part A: Your first priced proposal

How to review a drawing in TrueQty: check every camera, remove, add

Check every device TrueQty counted, take out what is wrong, and add what it missed. A tick means a person checked it, never that TrueQty was sure.

Who can do this
JuniorTeam leadAdmin

In this guide

  1. 01One device type at a time
  2. 02Step, check, take out
  3. 03Find what it missed
  4. 04Checked by a person

Step by step

  1. Open the drawing. A card says what TrueQty found, such as "73 devices found", with Devices found, Device types and Types to check. Click Start checking.
  2. Pick a device type under Check each device type in the left panel, such as the dome cameras. The drawing now shows only that type, and the bar above it says Showing only: with the type and how many.
  3. Look at them all at a glance, or step through them one at a time:
    • N, or Next device, moves to the next one, so you can see with your own eyes that it really is a device.
    • P, or Previous device, goes back.
    • Enter checks the one you are on.
  4. Take out anything that is not a device. Press Delete, or click Not a device. It leaves the count, and the total drops by one. Only Delete does this: Backspace does nothing on a drawing.
  5. Fix a device of the wrong type. Press C, or click Change type, and choose what it actually is. Press Esc if it was right after all.
  6. Read the line above the drawing. Many consultants print their own total, and TrueQty checks itself against it. "Close to the drawing's own total: found 72 cameras, the drawing says 73." means one is missing.
  7. Read the notes. A device type with something to read says so in the list, such as 1 note to read, and the note shows under it while the type is open. Here, one camera is named but not drawn: camera 33 is there, then a label for 34 with no symbol.
  8. Add it. Press A, or click Add missed devices, choose the type, and click where it belongs.
    • The type list opens on the drawing's own system, under List for, with that system's devices named as a consultant's BOQ names them. Every other type is below them.
    • The device is marked Added by hand, so anyone can see a person put it there.
    • Click Done adding when you are finished.
  9. Look at any count flagged under Check each device type. Some devices come in step, such as each lock with its door contact. A sheet where they differ says so, such as "12 electromagnetic locks and 11 door contacts on this sheet". It is a prompt to look for a missed or a doubled device, never a change to a count.
  10. Undo a slip. Placed one too many? Ctrl + Z, or Undo last, removes the last device you placed.
  11. Check the whole type when you are happy with the count. In the bar over the drawing, click Mark all 73 ... checked, which names the count and the type. The type now says Checked in the list. Next type moves on to the next one.
  12. Do the same for every other device type on the drawing: the door contacts, the locks and the card readers.
  13. Approve, or hand it over. A team lead or an admin clicks Approve counts, which puts the devices in the BOQ under their name. A junior clicks Send to team lead instead. See Approve a drawing.

Check it worked

The line above the drawing turns green when your count matches the drawing's own total, and the progress under Check each device type shows every type checked, for example 4 of 4 checked.

Nothing is ever destroyed

A device you take out is not deleted. Press Delete again, or click Put it back, and it is restored. Every change you make is recorded against your name.

A device you placed by hand is different: Delete, or Remove, takes it off the drawing altogether, and Undo in the message puts it back where it was. To move a ring that missed its device, remove it and place it again.

While you are adding devices, hold Space and drag, or drag with the mouse wheel pressed, to move around the drawing. Over the drawing the wheel zooms; to scroll the page, use the wheel over the narrow strip on the right of the drawing.

An approved drawing

An approved drawing opens for looking only. To change a count, TrueQty first asks Edit an approved drawing?, and Edit counts removes the approval, so the drawing needs approving again.

If your seat is read-only, you can look through any drawing, step through its devices and filter them, but not change its counts.

Keys at a glance

The same list is in More, Keyboard shortcuts.

Key What it does
N / P Next or previous device of the type shown
Enter Check the selected device, or uncheck it
Delete Not a device, or put it back. On a device added by hand, remove it
C Change the type of the selected device
A Add missed devices: choose a type, then click each one
Ctrl + Z Undo the last device you placed
Esc Close the topmost open thing, one at a time

Watch it done

Open on YouTube

The same steps, on the sample tender, in 2:19.

TrueQty Academy/CH 05/Review a drawing

Finished this guide?

Mark it done to track your way through the Academy.